SegwayChat
Home . Old Gallery

Go Back   SegwayChat > Segway Forums > Segway General Discussion

Notices

Segway General Discussion General discussion related to any model of Segways, miniPROs, or Ninebots. Please do not post non-Segway technology posts here; use the technology forum instead.

Old 05-09-2022, 11:25 AM   #1
DanDaMan
New Member
DanDaMan is on a distinguished road
 
Join Date: May 2022
Location: Alberta
Posts: 3
Default newbie - i180 flashes only red 4x on powerup

Just bought my first Segway, a i180 - got it for $200 CDN cause the PO said it had bad batteries. I'm pritty handy and unafraid of projects so I got it. Cosmetically it appears as in great condition.

So I left it plugged in over night and after disconnecting the cord I put the red key in - it immediately shows the grey display (startup test) for 1 second and then just starts to flash solid red 4 times with 4 beep/beep tones (no icon is displayed - just flashing red), and then it shuts off. Tried a few times and got the same thing. I downloaded a manual and could not find what this error means (the manual shows that all red displays should have an icon too?).

So I removed bought batteries (which are lithium 73V) and tested each on my multimeter - one was 79V and the other 80V. So what does that mean? Is it normal for the battery to be higher than the rating? Does this mean the batteries are good? Can a bad battery still show the proper volts but still be bad (ie. no capacity)? Also I see the PO opened the battery packs - if I reopen them is there some other test I can do to confirm battery are good?

Would really love some advice where to check next, and what my solid red light means. Thanks
DanDaMan is offline   Reply With Quote
Old 05-10-2022, 08:46 AM   #2
dgbint
Member
dgbint will become famous soon enoughdgbint will become famous soon enough
 
dgbint's Avatar
 
Join Date: Apr 2003
Location: Melbourne, VIC, Australia.
Posts: 979
5 yr Member HT/PT Owner
Default

Simple enough question, but lots of details needed for a good answer.

1
Are the batteries Segway batteries or aftermarket batteries ?
If Segway, they will have a serial number, which indicates how old they are.
Let me know.

2
What ever the outcome, batteries are complex, working on them and requires both special skills and special equipment. Beware and be very careful.

Michael
dgbint is offline   Reply With Quote
Old 05-10-2022, 09:59 AM   #3
DanDaMan
New Member
DanDaMan is on a distinguished road
 
Join Date: May 2022
Location: Alberta
Posts: 3
Default

Ok I have a bunch of updates and more questions, after spending hours googling and reading.

First, the red light I had was due my the outlet I had it plugged into - in short it was not plugged in and hence the battery was so low causing the red light and shutoff. After plugging into a working outlet for 12 hours the unit turn on and I got the green with full bars.

Went for a test ride - found that if I go slow (walking speed) I can ride 30+ minutes and still have >50% battery, but once I start going a little faster it goes to the red light with sad face and starts to shutdown - I tried it many times and this always happens. It goes to the red light and shutdown within seconds of going faster (but again if I go walk speed it is fine)?

So I started to take a closer look at the batteries. First, when I first start to charge my lithium batteries I get green charge light on both F and R, but one of the batteries went to red while the other eventually gets to the slow blinking green (suggesting one battery is good but other not). But when I removed both batteries, I found both at 82V suggesting both are at 100% charge. So I reinstalled both batteries and swapped (did this many times), and found that sometimes both batteries had the red light but other times both green blinking and other times just 1 green and 1 red. So in another words it is not consistent, but what is consistent is that in all cases both batteries would never go below 75V (even after the 30+ minutes of walk speed) and both would always charge up to 82V. Being both charge up, my BSM is good.

Even though both batteries are charging to 82V, could one or both still be bad, causing the error at a higher speed? If the batteries can still be an issue, can someone provide some details how I can test which cell/battery is actually bad? The PO already opened up both battery cases, so I was easily able to open one of them up (the one that originally had the red light). I pulled out the batteries with the pcb, and did some quick tests with my multimeter. Though since the overall battery was at 82V, I was not able to find any issues (if the battery was low voltage I would have easily been able to find the bad bank). But in my case with 100% voltage, what is the method to find the battery issue?

Thanks
DanDaMan is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:38 AM.
Copyright 2002-2022 SegwayChat.org.
All rights reserved. Not affiliated with Segway Inc.

FreshBlue vBulletin skin by
VayaDesign
Powered by vBulletin
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
SegwayChat Archive