02-05-2020, 03:04 PM | #1 |
Member
Join Date: Dec 2002
Location: In a house, Los Angeles, CA
Posts: 219
|
Loading a Segway I2 SE into a trunk
I am considering buying a car that is not a hatchback, a sedan that has a trunk that i cannot use the ramps to place the Segway into the trunk. Has anyone else devised a way of loading a Segway into such a trunk? Such as a portable hoist? Or a platform in the trunk that would life the base on to the ramp?
|
02-06-2020, 12:38 AM | #2 |
Junior Member
Join Date: Dec 2013
Location: Southern California
Posts: 47
|
I am watching this thread with great interest because I have the exact same situation.
Sent from my iPad using Tapatalk |
02-07-2020, 02:23 PM | #3 |
Junior Member
Join Date: Dec 2017
Location: New Jersey
Posts: 88
|
So, I've managed to load my Segway into my trunk by 1) Removing the leansteer bar; and 2) lifting by the lower cargo frames ... these guys: https://www.segwayunlimited.com/prod...ames-set-of-2/
It's heavy, but doable. |
02-09-2020, 03:09 AM | #4 |
New Member
Join Date: Mar 2018
Location: United States
Posts: 10
|
Does the car have a receiver hitch? If so you can get a platform that fits right into it with a fold down ramp. I bought two older Sarix carriers off ebay for about $150 each and built a double Segway carrier.
|
02-10-2020, 05:43 PM | #5 |
Member
Join Date: Jun 2016
Location: Ocean Springs MS
Posts: 242
|
The 'secret' is to install cargo bars on the Seg - Then they are easy to pick up by one or two people. Depending on the car, you may need to take the lean steer off completely and if this is the case, Seg makes a kit which allows you to remove and reinstall it quickly without any tools. It uses a cam and a lever to tighten the bolt. If your trunk isn't too small, you might just need to remove the upper half of the lean steer, which is even quicker and easier to do. We've used this method most all the time, but I do have the lever action bolt on one of my three Segs and have removed the complete lean steer several times. Picking up a Seg without the cargo bars is darned near impossible, so three sets of cargo bars were among our first purchases and boy, what a difference they make!
Don |
02-16-2020, 08:05 AM | #6 |
Junior Member
Join Date: Sep 2005
Location: Auckland, New Zealand.
Posts: 81
|
Have you considered buying a TriLift?
Have you considered buying a TriLift? This is an electrically operated power lift that attaches to your tow bar. It is a bit like a bike rack for your Segway PT, but electrically raises it and locks it into place.
The TriLift is mostly used for mobility scooters, but they make (or have made) an adaptor for the Segway PT. Or someone could make one for you quite easily. The following video clip is slow and loud but it shows how it works:
__________________
Segway New Zealand / Personal Transport Limited • Read the Segway NZ News blog at To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. |
02-18-2020, 06:14 PM | #7 |
Junior Member
Join Date: Oct 2009
Location: greenville, sc
Posts: 27
|
I tried to figure out how to do this for quite a while and haven't figured out a way to easily get it in and out of the trunk. Also when traveling I wanted to keep the trunk accessible for luggage or groceries, etc.
I've been using Segways as a mobility device for about 10 years. The only advice I can give is that putting a lift onto the back of a small car didn't work for me. I put a Segavator onto the back of a 1999 Toyota Avalon. It was more weight than the rear springs could handle. After hitting the bottom of the Segavator on the pavement numerous times, it jammed the screw actuator for the lift several times and finally locked it up hard enough that when I manually tried to unlock it it stripped the screw mechanism, ruining the lift. ( If anyone wants the a Segavator for parts I will give you mine. I'm off I-85 in South Carolina. I won't ship, you need to come pick it up. ) I couldn't find any kind of helper springs/airbags that would allow the car to handle the weight. The only solution I could come up with is a Bruno Chariot: https://www.bruno.com/scooter-lifts/chariot The bad thing is they retail for about $3500!!! I spent about a year looking for a used one on Craigslist and finally found one about 6 hours away for $650. You will have to put a hitch on the back of your car for another couple hundred dollars and run a wire to the battery for the higher current to run the lift up and down. The advantage of the Chariot is that with the Segway or other handicap scooter in the lifted position it only puts about 20 pounds of weight on the trailer hitch. Also backing the swivel wheel trailer is easy. My wife can't back a regular trailer but the Chariot follows the car naturally. I attached a wedge shaped box to the platform and use the straps that came with the Chariot to strap the Segway down and a small rope to keep the steering column from flopping around. I'm on my 3rd Segway and 2nd car with this setup and am still pleased with it. I've probably got 4000 miles on it. I do use a regular handicap lift on the back of my old pickup truck for short local running around. I'm sure you could design and build a platform to fit into the trunk that would hold the Segway up high in the trunk. You would have to keep the trunk lid open if you didn't want to lift the Segway and have the platform almost even with the top of the trunk. There just isn't much in the way of crane/lifts that can fold up so you can take it and the ramps with you in a car with a trunk. While typing this I wondered if you could make a light weight crane that plugged into a 1 1/4" receiver trailer hitch. It would probably need to be pretty high to lift the Segway over the trunk lip and might need to fold in half. It would be difficult, probably expensive to get made but doable. I don't come onto Segway Chat often so it may be awhile to respond to any questions that anyone may have. I apologize. |
02-18-2020, 07:03 PM | #8 |
Junior Member
Join Date: Oct 2009
Location: greenville, sc
Posts: 27
|
How about something like this adapted to mount onto a trailer hitch and use posts that slip into one another to make it high enough to get over the trunk lift.
https://www.harborfreight.com/12-ton...nch-61522.html You could weld/mount it to a modified hitch mount like this: https://www.harborfreight.com/ball-m...nch+ball+hitch with a mounting plate welded to it. I wouldn't want to pick up much weight with it. Don't rely on any of this to make something without seeking professional help. I don't want to be responsible for any kind of accident. |
02-19-2020, 01:47 PM | #9 |
Member
Join Date: Jan 2013
Location: Vancouver, WA
Posts: 122
|
'seghauler'
https://www.flickr.com/photos/davis_...7651617930416/
a 'hitch haul' rack and a couple of wood ramps and a couple of webbed motorcycle straps and you're good to go. Many local U-Hauls can install a hitch for you if you do not have one or this... Bruno 'curb-sider' lift https://www.bruno.com/scooter-lifts/curb-sider Last edited by dudeman1961; 02-19-2020 at 01:56 PM.. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|