08-06-2015, 06:02 AM | #1 |
Member
Join Date: Apr 2010
Location: Catlett VA
Posts: 386
|
how to hoist up a segway ?
Hi Folks:
I wanted to see if anybody had some suggestions that might help me out. I have 2 segs, an I2 and and SE. I currently haul them on the back of my SUV on a segvator. I am getting a handicap lift, like a little crane, that mounts inside my SUV, and it will pick up the seg, and that way I can easily haul it inside my SUV rather than outside the car. I had a few days last winter where the cold really stressed out the batteries on the segway, and it should work much better hauling it inside. The particular lift I will be using is demonstrated in the quick video accessed via the enclosed link. But my question is... how should I attach the lift strap to the segway to pick it up safely without damaging the segway ? They make all sorts of adapters to attach to the end of the hoist strap to connect to various wheelchairs or scooters. I am thinking initially that my best bet is basically a snap-link at the end to allow me to loop the hoist strap to a nylon strap that I rig to the segway. I have cargo bars on my I2, so a little strap between the 2 loops at the back on top of the cargo bars could hook to the hoist strap and should work. The SE I am not sure what to do with yet. There is a loop in the casting of the leansteer that would be convenient to attach to the hoist, but I dont think that is the smartest way to lift the SE. Maybe two small straps that basically straddle the batteries from front to back, one strap on each side and I could hook the hoist strap to those ? Let me know if you have any ideas and thanks for your help. http://www.bruno.com/big-lifter/?sea...570#tab-videos |
08-06-2015, 09:22 AM | #2 |
Member
Join Date: Jul 2013
Location: Arizona
Posts: 555
|
A nice 3" wide tow strap doubled around bottom... http://www.amazon.com/b?node=15737581
Maybe a 9 footer with loops on the end...2 straps under batterys...Loops on one side, then choke them through the closed end and tightened to top of base... It wont slide and balance should be good by the way you choke it... With that loop you could easily change the center of gravity on it...wish I could explain better.... If you lifted at the bars Im sure they would start bending them inword.... |
08-06-2015, 03:26 PM | #3 | |
Member
Join Date: Dec 2008
Location: SW Missouri, near Springfield
Posts: 875
|
Quote:
__________________
Lily Kerns ~~~~~~~~~~~~~ Faculty: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. |
|
08-06-2015, 05:52 PM | #4 | |
Member
Join Date: Dec 2008
Location: SW Missouri, near Springfield
Posts: 875
|
Quote:
Give them full credit for promptness though!
__________________
Lily Kerns ~~~~~~~~~~~~~ Faculty: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. |
|
08-07-2015, 05:27 AM | #5 |
Member
Join Date: Apr 2010
Location: Catlett VA
Posts: 386
|
Thank you for that idea, Lily. Why not ask them... didn't occur to me. I am going to the authorized dealer tomorrow with the Segway to check out the particulars and meet with the guys who do the installs and figure out the best way to do it. I am going to get in installed the week after labor day as I on vacation then and can do without the car. I'll post some pics when its done.
|
08-07-2015, 05:29 AM | #6 | |
Member
Join Date: Apr 2010
Location: Catlett VA
Posts: 386
|
Quote:
Thank you Airdale, I have a good idea what you are referring to. I see how it would choke down if you put one end through the loop on the other end and you could then move it and center it so its nice and balanced. That sounds like my plan for now. |
|
08-07-2015, 12:48 PM | #7 |
Member
Join Date: Dec 2010
Location: South Dakota
Posts: 327
|
Here is a link to a guy that developed a lifting collar to use with his Bruno lift. I have no idea if it's appropriate to lift the Segway in this manner or if the lifting collar is still available, but it looked interesting nonetheless. Maybe it's an example of what not to do.
http://dammon.com/slideshowsegway/sl...gway/index.htm |
08-10-2015, 05:49 AM | #8 | |
Member
Join Date: Apr 2010
Location: Catlett VA
Posts: 386
|
Quote:
|
|
08-10-2015, 04:09 PM | #9 |
Member
Join Date: Dec 2008
Location: SW Missouri, near Springfield
Posts: 875
|
I heard back from them and they don't make one for my car....2005 Subaru Impreza
__________________
Lily Kerns ~~~~~~~~~~~~~ Faculty: To view links or images in signatures your post count must be 5 or greater. You currently have 0 posts. |
08-10-2015, 07:25 PM | #10 |
Member
Join Date: Dec 2010
Location: South Dakota
Posts: 327
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|