11-14-2006, 08:49 PM | #11 |
New Member
Join Date: Aug 2006
Posts: 13
|
My Segway X2 worked for 1 day. Now it won't start & I get these codes:
My Segway X2 worked for 1 day. Now it won't start & I get these codes:
E042 with a ! symbol I removed and reset the batteries and the x2 worked again. I turned it off then started it up and got this error code: E04A with a wrench symbol I turned it off again then started it up and got this error code again: E042 with a ! symbol which I get every time now. Any suggestions other than driving 560 miles round trip to my nearest dealer? Thanks for the help. |
11-20-2006, 04:56 PM | #12 |
Advanced Member
Join Date: Nov 2004
Location: North west England, UK.
Posts: 3,043
|
Error code: E015
Discussed here: http://forums.segwaychat.com/showthr...305#post130305 Cause: "if I have the i2 in RBM against a wall, then step on and make a quick 180, I get a safety shutdown with an E015 error"
__________________
Gareth Brandwood The comments posted are made by the fat figners of the individual and do not necessarily represent the views of the brain. |
11-26-2006, 12:57 PM | #13 |
Junior Member
Join Date: May 2006
Location: Europe/Sweden/Linkoping
Posts: 54
|
Error code 205 means one of the controller board has a malfunction.
att the time this happend the machine was so new, and segway att Stockholm dident have anny spare part in stock. so they just gave me a new baseunit. |
11-29-2006, 12:07 PM | #14 |
New Member
Join Date: Nov 2006
Posts: 1
|
Another error code (i2)
E086 is an error in the propulsion subsystem.
If the problem keeps occuring, the base needs to be replaced. (And yes i found that out the hard way ) |
12-01-2006, 11:31 PM | #15 |
Senior Member
Join Date: Dec 2002
Location: Kenmore, WA, USA.
Posts: 2,097
|
E102
I've gotten this error with a safety shutdown four times now - twice in a row today. It appears to occur if I take off either uphill or downhill too soon after stepping on in balance mode. The 'hill' doesn't need to be at all steep either. Actually, it may not be a safety shutdown. It beeps like one, but doesn't shut off when I step off - I have to shut it off manually. I'll experiment to try to get more information.
__________________
35K miles in 15 years! |
12-06-2006, 10:47 AM | #16 | |
Senior Member
Join Date: Mar 2005
Location: Southern California, USA.
Posts: 1,921
|
From this post:
http://forums.segwaychat.com/showpos...2&postcount=10 Quote:
http://forums.segwaychat.com/showpos...11&postcount=8 (That is, swapping positions of the battery packs exchanged codes E102 & E10A) |
|
12-23-2006, 08:20 PM | #17 |
Member
Join Date: Aug 2006
Location: Cumming, GA USA
Posts: 634
|
Simply "E E" Was caused by ................................
Today, I rode to a Home Depot and parked (with security on) outside the front door to just buy a couple of light bulbs. When using the self check, I put the info key and helmet on the metal plate for goods just before scanning them. While walking back to the seg, I noticed "E E" was on the infokey. I couldn't get rid of it, so just removed the battery to reset it then everything was fine. I did have to reset the date, time, etc. Has anyone else experience this? I'm sure it had to do with being near the scanner.
__________________
Jim in Cumming, GA Proud to be a Redneck " We know that communication is a problem, but the company is not going to discuss it with the employees." (Switching supervisor, AT&T Long Lines Division) |
01-02-2007, 08:43 PM | #18 |
Member
Join Date: Jul 2003
Location: oakland, calif, USA.
Posts: 378
|
Error code: E407
Error code: E407
The Rear CU Board reports: Power base fault Recommended Action: If the same error code is persistent replace the power base or return to factory for service Much Regards,
__________________
slide4less |
03-08-2007, 12:38 AM | #19 | |
New Member
Join Date: Mar 2007
Posts: 2
|
e102
Quote:
I drained the batts just like the manual told me and no more codes so far-- my new x2 is working great. they say your x2 only works as good as the worst battery this rebalances them. anyway it worth a try. |
|
03-10-2007, 02:17 PM | #20 |
Junior Member
Join Date: Mar 2007
Posts: 53
|
e102 - Battery / board communication
After swapping batteries, I got an e102 message .. the off-board charger had gotten the contacts on the batteries dirty. If you use more than one set of batteries, check the contacts for cleanliness.
After cleaning the contacts (pencil eraser + air can method) the error disappeared. |
Currently Active Users Viewing This Thread: 6 (0 members and 6 guests) | |
|
|